The YD03-006 2 TON CROSS BEAM ADAPTOR is an auxiliary tool designed
specifically for "extending the load-bearing capacity and
adaptability of floor jacks". Addressing the pain points of
traditional jacks such as "narrow contact points easy to slip,
undercarriage easy to damage, and limited vehicle adaptation", it
takes heavy-duty steel structure and flexible adjustment design as
the core to achieve the core needs of "wide-range adaptation, high
safety protection, and non-destructive operation". It is suitable
for vehicle lifting scenarios such as auto repair shops, auto
maintenance stores, and personal garages. Its core advantages are
as follows:
- 2-Ton High Load-Bearing + Welded Steel Structure, Durable and Tough:Integrally welded from Q235 low-carbon steel, the cross beam
thickness is 8mm, and the welded joints are reinforced, with a
tensile strength of 375MPa. The cross beam deformation is ≤0.3mm
under 2-ton rated load, and there is no bending or fracture risk
even under short-term 2.2-ton overload pressure; compared with
ordinary stamping-formed adapters, the impact resistance is
increased by 60%, and it can be used with jacks to lift family cars
(about 1.2-1.8 tons) and compact SUVs (about 1.8-2 tons) for a long
time, with a service life of more than 8 years.
- 590-930mm Wide-Range Adaptation, Full Coverage of Multi-Vehicles:The cross beam working range supports 590-930mm free adjustment,
fixed by telescopic buckles at both ends — adjust to 590-700mm for
small sedans (e.g., Honda Fit, Toyota Vios), 700-800mm for compact
sedans (e.g., Volkswagen Lavida, Nissan Sylphy), and 800-930mm for
compact SUVs (e.g., Haval H6, Changan CS75). The vehicle adaptation
rate is over 95%, and one unit can meet the lifting needs of most
family vehicles.
- Rubber Lifting Plates + Safety Chain, Anti-Damage & Anti-Falling:Equipped with 2 adjustable rubber lifting plates (15mm thick),
with a contact area of 80cm² with the vehicle undercarriage, which
can not only increase friction (friction coefficient ≥0.85) to
prevent the adapter from sliding, but also avoid direct metal
contact with the undercarriage, eliminating scratches or dents on
undercarriage armor and pipelines; comes with a high-strength
safety chain (load-bearing ≥2 tons), which can prevent the adapter
from accidentally falling during lifting after connecting the
adapter and the jack, and the safety factor is increased by 100%
compared with the chainless design.
- 0-55mm Height Fine Adjustment, Precise Undercarriage Adaptation:The rubber lifting plates support 0-55mm height adjustment, which
can be fine-tuned by rotating the bottom knob
clockwise/counterclockwise — adjust to 0-20mm low height for
vehicles with low undercarriage (e.g., sports cars, low-slung
sedans) to avoid scratching; adjust to 30-55mm high height for SUVs
with high undercarriage to ensure stable contact, solving the pain
point of traditional jacks "fixed height, difficult to adapt to
some vehicles", with a lifting accuracy of ±2mm.
- Multi-Vehicle Lifting Maintenance in Auto Repair Shops:When repair shops serve multiple vehicle types such as sedans and
SUVs at the same time, the 590-930mm width of this adapter can
adapt to all vehicle models, and the 2-ton load-bearing covers the
weight of most family vehicles; maintenance technicians do not need
to frequently replace lifting accessories, and can safely lift the
vehicle for undercarriage inspection, tire replacement and other
operations after fine-tuning the height with rubber lifting plates,
adapting to the repair shop's needs of "efficient maintenance and
multi-vehicle compatibility".
- Vehicle Side/Front/Rear Overall Lifting in Auto Maintenance Stores:When auto maintenance stores need to lift the entire side, front
or rear of the vehicle, the adapter cross beam provides a longer
contact point, evenly distributing the weight to the undercarriage
load-bearing parts, avoiding undercarriage deformation caused by
local pressure; after fixing the safety chain, the lifting height
can reach 930mm, facilitating technicians to perform in-depth
operations such as gearbox maintenance and undercarriage armor
spraying, improving maintenance convenience.
- Daily Vehicle Maintenance in Personal Garages:When individuals perform maintenance such as oil change and tire
rotation on their family cars (e.g., Toyota Corolla, Honda Civic),
the 11kg lightweight design is convenient for single-person
carrying and assembly; the rubber lifting plates protect the
undercarriage paint and pipelines, and the 590-700mm width adapts
to family sedans. No professional operation experience is needed,
and it can be safely lifted with an ordinary floor jack, solving
the pain point of "no professional lifting equipment for personal
maintenance".
- Undercarriage Cleaning and Care in Auto Beauty Shops:When beauty shops perform undercarriage cleaning and rust
prevention for vehicles, the 0-55mm height adjustment of the
adapter can adapt to vehicles with different undercarriage heights,
and the rubber plates prevent cleaning fluid from corroding the
metal adapter; the undercarriage is fully exposed after lifting,
facilitating technicians to comprehensively clean the dirt in the
undercarriage gaps, and the safety chain ensures no falling risk
during operation, adapting to the beauty scenario of "fine care and
safety first".
A1:Yes. 1.9 tons does not exceed the 2-ton rated load, and the
product reserves a 10% safety margin (the actual safe load is about
2.2 tons). When in use, the adapter width should be adjusted to
800-930mm to ensure the rubber plates at both ends of the cross
beam fully contact the SUV undercarriage load-bearing beams; after
connecting the safety chain, lift the vehicle slowly. At this time,
the weight is evenly distributed, with no structural overload risk,
fully meeting the lifting needs of compact SUVs.
A2:Only two parameters of the jack need to be confirmed: ① The jack
is a floor jack with a removable saddle, and most Pittsburgh brand
and general floor jacks meet this requirement; ② The rated load of
the jack is ≥2 tons (matching the adapter's load-bearing). For
compatibility, simply remove the original saddle of the jack, align
the adapter interface with the top mounting hole of the jack, and
tighten the fixing bolts. The installation time is ≤1 minute, and
the compatibility is over 98%.
A3:Yes. The rubber lifting plates adopt a screw-fixed design. After
wear, replacement parts of the same model can be purchased
(available at brand after-sales service or industrial hardware
stores). The replacement steps are simple: ① Unscrew the fixing
screws at the bottom of the lifting plates with a wrench; ② Align
the new lifting plates with the mounting holes and tighten the
screws; the replacement time for a single lifting plate is only 3
minutes, no professional tools are needed, and ordinary users can
operate it, with the performance consistent with the new plate
after replacement.
A4:Yes. The adapter cross beam adopts a mechanical structure of
"thickened middle + anti-slip ends". When lifting one side of the
vehicle, the weight is evenly transmitted to the jack through the
cross beam, and the rubber plates have a friction coefficient of
≥0.85, which can prevent the vehicle from sliding; combined with
the safety chain fixation, even if the lifting height reaches
930mm, there is no tipping risk; tests show that lifting one side
of a 1.8-ton vehicle for 30 minutes, the cross beam has no obvious
deformation, and the stability fully meets the maintenance
operation needs.
360 Swivel Blue Gearbox 300KG Engine Hoist And Stand
