Home > Electrical Equipment & Supplies > Wires, Cables & Cable Assemblies > Cable Manufacturing Equipment >

Iec 60702 1 Bending Test Apparatus

1-10 Results for

iec 60702 1 bending test apparatus

from 8 Products

manual IEC Test Equipment IEC 60811 Cold Bend Test Apparatus For Cables Sheaths And Insulation

... bending performance of wire and cable at low temperature. The equipment is mainly composed of low temperature thermostat, winding device and material testing system. It is suitable for circular wire and cable with outer diameter less than or equal to...

Guangzhou HongCe Equipment Co., Ltd.

Address: No.6-39, Yaogu Farm, Shibi No.3 Village, Shibi Street, Panyu District, Guangzhou

IEC 60702-1 Clause 13.6 Electric Vehicle Cables Bending Test Apparatus

... to the standard requirement of IEC 60702-1 clause 13.6, and etc. It is used to test the bending performance of copper core or copper alloy sheathed mineral insulated general wiring cables to verify their reliability. It uses the motor to ......

Sinuo Testing Equipment Co. , Limited

Address: Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone, Shibi Street, Panyu District, Guangzhou, China

IEC 60702-1 Clause 13.6 Bending Test Apparatus For Mineral Insulated Cables

...IEC 60702-1 clause 13.6, and etc. It is used to test the bending performance of copper core or copper alloy sheathed mineral insulated general wiring cables to verify their reliability. It uses the motor to ......

Sinuo Testing Equipment Co. , Limited

Address: Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone 511495, Shibi Street, Panyu District, Guangzhou, China

Manual Control 60811 IEC Test Equipment Cold Bend Testing Apparatus

... Methods for general application-Test at low temperature clause 8.1 and 8.2 and figure 1. Figure 1 Cold Bend Test Apparatus Application: This test is intended in general for cables with an overall diameter up to and including 12.5 mm, or for flat cables, a...

HJ AUTOMATIC CONTROL TECHNOLOGY CO., LTD

Address: No.6-36, Yaogu Farm, Shibi No.3 Village, Shibi Street, Panyu District, Guangzhou, Guangdong, China

IEC 60598-2-21 Figure 2 Cold Bend Test Apparatus To Measure Dynamic Bending Performance Of Wire And Cable

IEC 60598-2-21 Figure 2 Low-temperature Winding Test Machine Overview Product description This Cold bend test apparatus is used to measure the dynamic bending performance of wire and cable under low temperature conditions, and is suitable for outer diameter less than or equal to 12.5mm round wire and cable or round insulated wire core is the wire and cable industry to test the bending......

KingPo Technology Development Limited

Address: RM C, 13/F, HARVARD COMMERCIAL BUILDING, 105-111 THOMSON ROAD, WAN CHAI, HK

AC220V 50HZ Power Cord Flexing Test Apparatus With Digital Display

...Adjustable Bend Angle Product information: This test apparatus checks the protection of the supply cord where it enters the appliance. It conforms to the standard requirement of IEC60335-1 clause 25.14. Appliances provided with a ......

Dongguan Kingpo Technology Limited

Address: RM C, 13/F, HARVARD COMMERCIAL BUILDING, 105-111 THOMSON ROAD, WAN CHAI, HK

AS/NZS3112 Figure 2.8 Pin Bending Test Equipment

AS/NZS3112-Figure 2.8 Application of force for pin bending test AS/NZS3112-Figure 2.1 (in part) dimensions of plugs AS/NZS3112-Figure 2.2 Apparatus for flexing test AS/NZS3112-Figure 2.3 Form of pin AS/NZS3112-Figure 2.4 Dimensions of insulaton on ......

Guangzhou Shice Equipment Co., Ltd.

Address: #1,chencongxi10xiang,chencongcun,qiaonanjiedao,panyu,Guangzhou

Submit your “iec 60702 1 bending test apparatus” inquiry in a minute :

*From:	Your email address is incorrect!
To:	Guangzhou Shice Equipment Co., Ltd. Products: AS/NZS3112 Figure 2.8 Pin Bending Test Equipment
*Subject:	Your subject must be between 10-255 characters!
*Message:	For the best results, we recommend including the following details: --Self introduction --Required specifications --Inquire about price/MOQ Your message must be between 20-3,000 characters!
	Please reply me within 24 hours. Yes! I would like your verified suppliers matching service! Yes! If this supplier doesn't contact me in 3 days, I want everychina.com to recommend me more suppliers.

Submit “iec 60702 1 bending test apparatus” inquiry

*From:
Your email address is incorrect!
To: Guangzhou HongCe Equipment Co., Ltd.
*Subject:
Your subject must be between 10-255 characters!
*Message:
For the best results, we recommend including the following details: --Self introduction --Required specifications --Inquire about price/MOQ Your message must be between 20-3,000
Yes! I would like your verified suppliers matching service!

Inquiry Cart 0